How To Install Tub Shower Wall Panels?
If you want to remodel your bathroom, a simple solution for the shower or tub is to finish it with fibreglass, acrylic or PVC surround panels.
This is a good choice using glued wall panels-is so an inexpensive and easy way to remodel your shower or bathtub alcove just need minimal effort.
Panels usually are attainable in 3 or 5 piece kits as well as two separated placement types. These are sturdier and thicker items particularly equipped to be affixed immediately to wall studs.
You Will Need:
| Materials | Tools or Equipment: |
|---|---|
| Chemical caulk remover | Screwdrivers |
| Masking tape | Utility knife |
| Panel adhesive | Plastic putty knife |
| Adhesive wall panel kit sized for | Tape measure |
| Your shower or bathtub | Level |
| Silicone bathtub/kitchen caulk | Jigsaw with fine-tooth |
| panel blade | |
| Drill with hole saws | |
| Caulk gun | |
| Notched trowel | |
| Sandpaper |
1. Ready Up The Walls
Adhesive wall kits can be placed only regarding the flat wall surface in the right condition such as drywall or tile. Where the panels are glued and your walls need to be proper clean so as to the adhesive will create a better adjustment.
After repairing and cleaning your wall surfaces, eliminate all the handles as well as the trim work for the tub or shower valves with a plastic putty knife and utility knife, just cut the caulk seals surround the tub or shower base. Deductively chemical caulk remover can assist any obdurate caulk residue. To appropriately place the new wall panels, however, you will require smooth, plane edges on the shower or bathtub base.
2. Check The Panels Fitting
Sometimes the panels of the surround kit fit the existing space properly, as they are basically sized to match stock bathtub and shower bases. Though it is probable you will necessary to trim panels to match, and so difficult to fit before you start the installation.
Put in the panel for the behind wall against the wall and tape the panel in exact place with strips of masking tape.
Then, install the side panel and the forward panel on the walls, by using masking take. Inspect the fit of the panels and all edges. This is not unusual for a tub or shower base to be out of balance, you may also require trimming the bottom of the panels and allowing adjustments to the right fit.
Tip: If your kit applies corner panels, secure to test-fit these in appropriate locations.
3. If Needed Cut The Panels
When the panel fitting procedure presents that cutting task is necessary, then you can use masking tape to trace cutting lines on the panels take aside the panels and apply a jigsaw with a fine-tooth panel blade for cutting the panels to the required size.
4. For The Faucet And Shower Cut The Holes
When you cut the holes for the faucet and showerhead needs diligent measurement of the onward wall, disposing these measurements to the onward surround panel.
Mark the vertical and horizontal distances of the showerhead stub-out and faucet stems, just measuring from your wall corner as well as from the edge of the tub or shower base. Dispatch these measurements to the onward surround panel.
Tip: You can also use a big sheet of cardboard cut to fit the onward surround panel to make a template for only drilling holes for the surround panel.
Deal with a drill or hole saws to cut holes accurately for the showerhead and faucet valves on the onward surround panel. If the holes are enough large, it is easily fit the valve stems, and for small enough the trim plates will cover the holes properly.
5. Associate Adhesive To The Behind Wall
Start the placement of the behind wall. With a panel adhesive particularly equipped for your panel’s type, use zigzag beads of caulk over the behind wall. And apply a notched trowel to extend the adhesive on a level over the wall surface. Ensure keeping the adhesive interior the marked lines.
6. Location Of The First Panel
Carefully locate the back panel along with press it contrary to the wall where the whole panel creates contact with the adhesive. Now pull the panel simply away from the wall for around thirty seconds. It accommodates the solvents in the adhesive to normally misuse and develop adhesion.
7. Put The Remaining Panels
Do again the former steps for the remaining panels pursuing the special instructions of your kit. A few 5-panel kits are equipped for the corner panels that are placed after the plane panels are in the proper position.
8. Need To Caulk All Joints
Now dry the panel adhesive minimum of 24 hours, and apply a high-grade silicone bath or kitchen caulk for sealing around the top of the surround panels.
9. Complete The Placement
Place the showerhead, handles, and tub spout and escutcheon plates in accordance with the manufacturer’s directions. Assure the escutcheons properly cover the holes, and then caulk around the fixtures.
Summary
To summarize this discussion we can say that, it is not a troubling task to install tub or shower surround panels if you follow our above instructions step by step.
Then your function will be easier and simpler.
